Twój przyrząd sprzedaje dokładność. Zmontujemy jego elektronikę powtarzalnie: od jednej sztuki po serię, z jakością, którą mierzymy i pokazujemy.Your instrument sells accuracy. We'll assemble its electronics repeatably: from a single unit to series production, with quality we measure and show.
[ Anatomia przyrząduInstrument anatomy ]
Czujnik zbiera sygnał, ale o wyniku decyduje elektronika: tor pomiarowy, przetwornik, procesor. Ktoś musi ją zmontować powtarzalnie, od prototypu po serię.A sensor picks up the signal, but the electronics decide the result: the measurement chain, the converter, the processor. Someone has to assemble them repeatably, from prototype to series production.
[ 01 / 04 ] InterfejsInterface
Wyświetlacz, klawiatura i złącza na jednej płycie: elementy 0201 tuż obok złączy przewlekanych. SMT i THT u jednego wykonawcy.Display, keypad and connectors on one board: 0201 parts right next to through-hole connectors. SMT and THT with one contractor.
[ 02 / 04 ] PomiarMeasurement
Przetwornik i wzmacniacze w obudowach fine-pitch, wokół precyzyjne elementy pasywne 0201 i 01005. Raster 0,5 mm montujemy standardowo, 0,4 mm po dodatkowej walidacji.A converter and amplifiers in fine-pitch packages, surrounded by precision 0201 and 01005 passives. We place a 0.5 mm pitch as standard and 0.4 mm after additional validation.
[ 03 / 04 ] PrzetwarzanieProcessing
Procesor w BGA 0,5 mm albo w QFN, obok pamięć. Połączenia ukryte pod obudową sprawdzamy na X-Ray.A processor in a 0.5 mm BGA or a QFN, with memory beside it. Joints hidden under the package are checked by X-ray.
[ 04 / 04 ] ZasilaniePower
Gniazda, złącza i elementy mocy osadzamy w otworach: ręcznie oraz selektywnie na ERSA Versaflow. Płytki już od 50 × 40 mm.Sockets, connectors and power components go through-hole: soldered manually and selectively on an ERSA Versaflow. Boards from 50 × 40 mm.
[ ZakresScope ]
Techbit to producent kontraktowy (EMS). Pracujemy na Twojej dokumentacji i według Twoich wymagań.Techbit is a contract manufacturer (EMS). We work from your documentation and to your requirements.
[ Gdzie pracuje ta elektronikaWhere these electronics work ]
/Przyrządy przenośnePortable instruments
/Aparatura laboratoryjnaLaboratory equipment
/Czujniki i przetwornikiSensors and transmitters
We don't just promise quality. We measure it and share the results.
Short runs, the smallest components, substitutes, quality, testing and certificates.
Yes. Technically, we can assemble as few as one unit, and cost-effective production runs typically start at around 20 units. For small runs we do not apply a single threshold: if you are considering several quantities, include them in your inquiry and we will compare them in the quote.
We place 0201 and 01005 components as standard. 03015 assembly depends on the project. We handle a 0.5 mm pitch, while a 0.4 mm pitch requires additional validation. We confirm that your design matches the line's capabilities before the quote.
No. We first review the BOM, component availability and alternative sources, then agree the procurement scope. We buy only after your approval. In the BOM, identify critical items and components without approved substitutes.
We perform AOI off-line, on a separate machine (Mirtec MV-3U), and use off-line X-ray inspection for QFN and BGA packages (FocalSpot). We do not have SPI, so an SPI requirement is discussed before the quote.
We include functional testing once its scope is agreed and we have received the tester and instructions. Adjustment and calibration stay on your side.
ISO 9001:2015. Requirements beyond that standard, such as industry standards for measuring equipment, are discussed before the quote. If we cannot fully support something, we say so at the start.
BOM, Gerber files and Pick&Place data are enough. We answer phone calls the same day and emails within 24 h.